Scratch built from photographs taken in 1970 HonKong
Meet the crew from the Junk! A tough looking bunch.

I found out that expended synthetic wine bottle corks serve well as boat fenders. I usually never throw anything away, just in case it has a purpose.
The funny thing is, I have numerous boxes of this stuff, and most of it has been forgotten! Reckon it's time to do some filtering.
HAVE A SAFE RC BOATING DAY!

Modified from an original by the late great Tony Dewsbury

Imara tug, remodelled from an original built by the late Tony Dewsbury, on it's first lake trial. Thanks to Jerry Hayes for the video (and encouragement!)

...and some rowing marines. This was a good show to see some quirky watercraft. Not easy recovering the smaller lifeboat but they did it.

Building a German Police launch right now and thought that the radar scanner components were a bit 'heath robinsonish', so decided to see if I could make an alternative unit.

Photo 1 shows the Radar scanner parts obtained from MMB (ebay) for the princely sum of ONE POUND !!!!! plus 28p postage, and construction is of a medium soft resin that isn't prone to breaking or splitting when shaped or drilled, and a short length of 2mm brass rod becomes the drive shaft. This particular unit has a 44mm sweep bar but there are many other sizes available

Photo 2 shows the drive motor which operates on voltages between 1.5 and 6v, ideal for the control driver which is the next item. Available from saih.tan on Ebay for under 7 pounds, and if the motor is mounted on a removable bracket as I have done, this unit can be used in several models without the need for major 'surgery', the motor and radar shaft being connected with a short piece of rubber tubing

Photo 3 shows the receiver driven radar motor speed control which operates from an auxiliary receiver channel and takes the motor voltage from the main receiver supply, thus obviating the need for a separate supply and switch.
This unit is available from www.mr-rcworld.co.uk and costs a staggering 14.50 post free sheesh !

I must add here that I am in NO way connected to any of the suppliers mentioned here, but just though some other modellers may be interested in 'home brew' accessories and suchlike.

AFTER RECEIVING LONG-AWAITED GLOBALLY SOURCED COMPONENTS, I DID A PRELIM DRIVELINE INSTALL/DRY FIT ON THE USCG 140'ER. 4MM SHAFT/BOX & RABOESCH 5-BLADE SKEWED WHEEL ARE FROM CORNWALL BOATS (UK), THE MOUNT AND U-JOINT COUPLER ARE BBQ ROUTISSERIE COMPONENTS. BTW-THERE'S A 3/16" ID CYLINDRICAL CENTER SUPPORT BEARING BETWEEN THE COUPLERS. THEY ARE NORMALLY USED ON "FIDGIT SPINNERS"

This working boat is an East Coast Fisherman’s Skiff, paint colours as available.

Travelled around quite a few shows this year and caught some great action of some superb models on water. Compiled into one relatively short vid. Filmed in UltraHD / 4K resolution. Looking forward to catching a lot more boat action in 2018. Enjoy !

Scratchbuilt WW2 1/24 Scale Vosper 73' Type 1 MTB. Built in 2016, in company with a friend's 1/24 scale BPB MGB.
The Vosper hull is built from balsawood and fibreglass. The upper deck and superstructure is from balsawood. The weapons and fittings are from brass, aluminium and plastic. The 20mm and gunner can rotate.

The seats are all installed and soon it will be time to sand, but with temperatures of -21C in the garage shop area where the power belt sander is located, the job of sanding will wait a bit.

Does anyone have a suggestion for a small outboard motor?

So glad to have this scrollsaw in the shop which has made cutting the bottom boards a very easy task. I cut the chines from Ash using this saw too with a fine blade. Look closely and there is a plexiglass cover on the table to give me a zero clearance around the blade hole, thus keeping small parts from falling under the table. A shop vac is attached to draw away the fine dust that this machine produces. My lungs are greatful too.🤓